TBH30 4-1/2 x 4-1/2 PLAIN BEARING HINGE
Usually Ships: 1-3 Business Days
TBH30 4-1/2-Inch x 4-1/2-Inch Standard-Weight Plain-Bearing Hinge
Our TBH30 is a 4-1/2-inch x 4-1/2-inch full-mortise plain-bearing hinge. The commercial hinge catalog identifies this model as standard weight, .134-inch gauge, and template type. Select it for an opening whose hardware schedule calls for this configuration, checking the preparation and door requirements before ordering.
TBH30 Specifications
- Part number: TBH30.
- Nominal size: 4-1/2 inches x 4-1/2 inches.
- Gauge: .134 inch.
- Weight classification: Standard weight.
- Bearing: Plain bearing.
- Mounting: Full mortise.
- Preparation: Template type.
Full-Mortise Fit
Our TBH30 has one leaf recessed into the door and the other recessed into the frame. Compare both mortises with the supplied hinge so the leaves seat at the correct depth. Overall dimensions, leaf thickness, screw positions, and the prepared corner profile all matter when replacing existing hardware.
Plain-bearing construction is distinct from a ball-bearing hinge. Select the bearing arrangement and hinge quantity for the actual door weight, width, height, frequency of use, and attached hardware. Do not assume that a hinge is suitable simply because its nominal size matches the old one.
Finish Selections
- ALUM, as identified in the selector.
- DURO, as identified in the selector.
- US10A, as identified in the selector.
- US10B, Antique Bronze Oiled.
- US15, Satin Nickel.
- US15A, Satin Nickel Blackened.
- US26, Bright Chrome.
- US3, Bright Brass.
- US32D, Satin Stainless Steel.
- US4, Satin Brass.
- US5, Antique Brass.
- USP, Primed Gray.
Choose from the actual selections offered here. Confirm any specified base material separately; a finish designation does not establish that every selection shares the same material construction.
Practical Applications
- Scheduled plain-bearing openings: Use where TBH30 is the specified standard-weight configuration.
- Replacement hardware: Match the actual hinge and preparation before replacing worn components.
- Finish coordination: Choose a listed finish to coordinate the opening's visible hardware.
Everyday example: A maintenance installer is replacing a worn hinge on a scheduled, low-frequency door. They confirm TBH30 on the hardware schedule, compare the 4-1/2-inch dimensions and .134-inch leaf gauge with both mortises, and check the screw pattern. After supporting the door and fitting the hinge, they test clearances and reliable latching.
Installation Guidance
- Verify the application: Confirm actual door dimensions, weight, use, required hinge count, and other hardware loads.
- Review the exact template: Compare leaf dimensions and screw positions against the existing door and frame.
- Inspect receiving material: Repair damaged preparation, stripped fastening points, or inadequate support before fitting.
- Confirm fasteners: The TBH30 template references #12 x 1-1/4-inch wood screws and #12-24 x 1/2-inch machine screws. Verify supplied contents and suitability for the actual substrate.
- Maintain alignment: Keep hinge axes consistent and avoid using screws to force misaligned leaves into place.
- Test the door: Check for rubbing, binding, uneven clearances, and unreliable latch engagement.
Problems It Helps Address
- A specified plain-bearing hinge needs replacement: Provides the identified TBH30 configuration.
- Preparation must match: Offers exact model dimensions and a matching template for comparison.
- Hardware needs a coordinated appearance: Offers the listed finish choices.
Selection and Care
Do not substitute this plain-bearing model for a ball-bearing or heavy-weight hinge without checking the complete hardware requirements. Closer-equipped, high-frequency, heavy-door, and rated-opening applications require particular attention to the specified bearing arrangement and approved assembly.
Confirm the purchase quantity and fastening contents before ordering; catalog packing counts do not establish the number supplied by a selected purchase. Do not infer a universal door-weight capacity, fire rating, or NRP configuration from the hinge size.
Use finish-appropriate cleaning methods and periodically inspect alignment and screw tightness. Investigate looseness or binding promptly rather than continuing to force the door.