BKICK Stainless Steal Kick Plates

Write A Review
Regular price $43.10
Sale price $43.10 Regular price $0.00
Unit price
-US32D-Satin Stainless Steel
Ask a question

Ask a Question

* Required fields

Size guide Share

BKICK Stainless Steel Kick Plates

Usually Ships: 1-3 Business Days

The Cal-Royal BKICK Stainless Steel Kick Plates add a protective surface to the lower face of a compatible door, helping reduce everyday scuffs and incidental contact marks. This listing offers 0.050" thickness in US32D-Satin Stainless Steel, with multiple plate sizes and screws included.

Choose the Correct BKICK Part Number

The manufacturer identifies plate sizes as height x width. Available size options in this listing are:

  • BKICK434: 4" high x 34" wide.
  • BKICK822, BKICK826, BKICK828, BKICK830, BKICK832: 8" high x 22", 26", 28", 30", or 32" wide, respectively.
  • BKICK1022, BKICK1026, BKICK1028, BKICK1030, BKICK1032: 10" high x 22", 26", 28", 30", or 32" wide, respectively.
  • BKICK1034, BKICK1040, BKICK1042, BKICK1046: 10" high x 34", 40", 42", or 46" wide, respectively.
  • BKICK1234: 12" high x 34" wide.

Measure the door face: Select the plate dimensions, not merely the nominal door size. Allow the necessary clearance from frame stops, seals, floor, and adjacent hardware. Catalog sizes beyond the options above are not established as selectable in this listing.

Practical Uses

  • Office and service-area doors: Protect the lower surface where footwear and routine traffic leave marks.
  • Renovations: Add a satin stainless steel face to a sound door while coordinating with nearby fittings.
  • Replacement projects: Replace a worn plate after comparing dimensions, thickness, and the actual mounting-hole pattern.

Everyday example: A utility-room door shows repeated shoe marks below the handle. An appropriately sized BKICK plate places a metal surface over that contact area. Before installation, the installer checks that the plate and screws clear the frame and do not interfere with the door's operation.

Installation and Fit Checks

Check the surface: Confirm the door has sufficient flat area and sound material for fastening. Repair underlying damage first; a kickplate is not a structural repair or a reinforcement for a weakened door.

Confirm the mounting pattern: Use the actual plate to check hole locations before drilling. Do not assume plates of different sizes or another manufacturer's plate use the same spacing. Center or position the plate as required by the specific opening, maintaining clearances.

Verify fasteners: Confirm supplied hardware, suitable screw length, and adequate fastening depth for the actual door construction before installation. Use the applicable instructions and actual plate to establish the mounting pattern for the selected size.

Finish and test: Fasten according to the applicable guidance without overtightening or distorting the plate. Check that the door closes and latches freely afterward. Confirm permitted preparation before modifying a specially rated door assembly.

Problems It Helps Address

  • Lower-door scuffing: Adds protection within the chosen coverage area.
  • Surface wear from everyday contact: Provides a metal face on an otherwise sound door.
  • Unclear replacement sizing: Model-specific height and width references help distinguish the offered options.

Product Details

  • Series: BKICK
  • Material: Stainless steel; no specific alloy grade established here
  • Offered thickness: 0.050"
  • Offered finish: US32D-Satin Stainless Steel
  • Fasteners: Included; verify suitability for the actual door construction
  • Manufacturer standards reference: ANSI/BHMA J102

Application limits: A kickplate is surface protection, not an impact-rated barrier or a security reinforcement. The catalog describes optional UL-labeled versions ordered with a “UL” prefix; this listing does not establish that a UL-labeled configuration is included. Confirm the exact supplied plate and opening requirements before use on a rated assembly.

Manufacturer References