CR2704 SADDLE THRESHOLDS 1/2" H X 4"
CR2704 Saddle Threshold, 1/2-Inch High x 4-Inch Wide
Our CR2704 is a commercial saddle threshold with a 1/2-inch-high x 4-inch-wide profile. Use it where the specified opening requires this profile, after checking floor elevations, door clearance, adjacent finishes, and the complete door-bottom arrangement. Available length selections are 36, 48, 72, and 96 inches, with Alum or Duro finish choices.
Practical Uses
- Specified commercial openings: Fit the documented profile across the bottom of the frame.
- Replacement work: Match the existing threshold's height, width, length, and installation details rather than selecting by appearance alone.
- Renovations: Coordinate the threshold with changed flooring, door-bottom hardware, and the door's closing path.
Everyday example: A maintenance team is replacing a threshold at a commercial opening. They confirm that CR2704's 1/2-inch height and 4-inch width match the specified detail, measure the frame opening, and choose sufficient stock length. They cut and notch the threshold as required, secure and seal it according to the instructions, then cycle the door to confirm that it still self-closes and latches.
Profile, Length, and Finish
Defined profile: The 1/2-inch height and 4-inch width are cross-section dimensions, not the stock length. Check the complete floor transition, including carpet or other adjacent finishes, before installation.
Cut-to-fit preparation: The exact installation instructions call for cutting the threshold to the full width of the opening, with end trimming and notching where necessary to accommodate side-jamb stops.
Finish selection: Alum and Duro correspond to the installation guide's Mill Aluminum and Duro finish references. Confirm the selected finish against the surrounding hardware and project specification.
Optional coating: The existing product information identifies Sure Step non-slip abrasive coating as an ordering option. Do not assume that this coating is included with the standard Alum or Duro selection; confirm availability and ordering details separately.
Installation Guidance
- Measure first: Measure the opening at the bottom of the frame and check the required finished length.
- Check clearances: Confirm profile height, floor levels, and the relationship to any door-bottom seal.
- Prepare the ends: Trim and notch only as required for the side-jamb stops and the actual opening.
- Mark through the predrilled holes: Drill suitable pilot holes and fasten using the specified installation method.
- Seal the perimeter: The guide requires sealing both ends and along the sides.
- Test the door: Operate it multiple times to verify that the installation does not prevent self-closing and latching.
The existing listing specifies #10 x 1-1/2-inch wood screws. Verify the supplied fasteners and their suitability for the actual substrate before fitting. Do not assume a wood-screw arrangement alone is suitable for concrete or another floor construction. General family references to brass or stainless thresholds do not establish that those materials are offered by this listing.
Problems It Helps Address
- A specified threshold is missing or worn: Provides a defined replacement profile and selectable stock lengths.
- The threshold needs fitting around jamb stops: Supports measured cut-and-notch preparation in accordance with the exact guide.
- Floor and door-bottom details need coordination: Makes clearance, sealing, and closing checks part of the installation process.
Rated-Opening and Accessibility Coordination
The exact CR2704 guide identifies UBC 7-2 (1997), Category J and a 3-hour positive-pressure reference, with material-use limits for specified listed steel frames and classified door constructions. It states up to 3 hours for the specified hollow-metal steel-composite construction, up to 1-1/2 hours for wood-composite construction, and 20 minutes without hose stream for wood-core construction. These are conditional component-use references, not a universal rating for every installed opening.
For a rated assembly, confirm the exact threshold, door construction, frame, and installation against the applicable listing and project requirements. For an accessible route, have the responsible project professional verify the installed threshold profile, floor transition, clearances, and complete opening. Neither the threshold nor a reference logo alone establishes compliance.
Care and Matching Documents
Keep the threshold clear of debris and inspect fasteners, perimeter sealing, and door movement periodically. Address looseness, damaged sealing, or interference with closing before continued use.
Usually Ships: 1-3 Business Days