PG-601 PERIMETER GASKETING
PG-601 Aluminum-Channel Perimeter Gasketing with Vinyl Insert
Usually Ships: 1-3 Business Days
Our PG-601 perimeter gasketing combines an aluminum channel with a vinyl insert to seal the gap between the door and jamb along the header and both sides. The installation guide permits use on wood or metal door jamb frames and calls for light, even seal contact with the closed door.
Profile Details
- Part number: PG-601.
- Construction: Aluminum channel with vinyl insert.
- Listed width: 1/4 inch, 6.4mm.
- Listed profile height: 7/8 inch, 22.2mm.
- Listed total height: 1-1/8 inches, 28.55mm.
- Application: Header and both sides of the door jamb.
- Frame compatibility: Wood or metal jamb frames, subject to suitable preparation and fastening.
Size and Finish Choices
- Available size selections: 36 inches x 84 inches, 48 inches x 84 inches, 48 inches x 96 inches, 72 inches x 84 inches, and 72 inches x 96 inches.
- AV: Mill Finish Aluminum with Vinyl Insert.
- DV: Dark Bronze Anodized Aluminum with Vinyl Insert.
Measure the actual header and both jambs before choosing a size. The guide calls for cutting pieces to the required length. Confirm the supplied piece lengths and configuration for the selected option rather than treating a size label as a substitute for measuring the opening.
Light, Even Contact Around the Door
Our PG-601 places the vinyl seal in an aluminum channel mounted at the door stops. Correct positioning matters: the guide directs the installer to close the door and bring the seal into light, even contact, then secure it through the slotted holes. Excessive pressure is not a substitute for a properly aligned door and can interfere with closing or latching.
This perimeter application serves the top and sides of the opening. Review the bottom gap and threshold separately; do not assume that perimeter gasketing alone completes the weather-seal arrangement.
Practical Uses
- Prepared wood or metal frames: Fit where the stop arrangement and project requirements permit this profile.
- Perimeter-seal replacement: Compare profile dimensions, condition of the stops, and the required seal contact.
- Opening maintenance: Address missing or poorly positioned perimeter gasketing after correcting door alignment.
- Finish coordination: Choose AV or DV to suit the visible frame and hardware finishes.
Everyday example: An installer is replacing worn gasketing on a service door. They measure the header and both jambs, select the appropriate PG-601 size and finish, and fit the header first. With the door closed, they establish light, even contact, fit the side pieces, and cycle the door to confirm that the latch still engages reliably.
Installation Guide
- Prepare the opening: Confirm door alignment, stop condition, and a suitable fastening substrate.
- Fit the header first: Measure, mark, and cut the header piece to the required length.
- Position with the door closed: Establish light, even seal contact and mark the centers of the slotted holes.
- Prepare pilot holes and fasten: Follow the guide and verify the provided screws. The guide references #6 x 5/8-inch screws for wood and metal doors.
- Fit both jamb pieces: Use the header as the guide and fit the sides to meet the header above and threshold below.
- Test and adjust: Open and close the door several times, check sealing and latch engagement, and reposition the gasketing as needed before retightening.
Problems It Helps Address
- Gaps at the header and jambs: Provides a vinyl-contact perimeter seal.
- Uneven seal placement: The guide's slotted-hole positioning procedure supports fitting and adjustment.
- Worn perimeter gasketing: Supplies an identified replacement profile to compare with the opening.
Selection and Care
Confirm compatibility with the complete door, frame, threshold, and required hardware. Any fire, smoke, sound, or other performance requirement must be verified for the exact product and complete assembly; this description does not assign a universal rating.
Inspect the vinyl insert, channel, fastening, and contact periodically. Keep the sealing surfaces clean, and address looseness, damaged inserts, or binding. Recheck closing and latching after adjustments.